|  | PANEL ASSEMBLIES |  |  | 
	| 1 | 12H3005 | Panel, front, top, assy |  |  | 
	| 1A | 12H7001 | Panel, top, upper |  |  | 
	| 1B | F2028100 | Screw, captive, .19 x .54 fast lead, phil pan hd |  |  | 
	| 1C | F2027100 | Screw, #8-32 x 3/8", phil pan hd |  |  | 
	| 1D | S2113900 | Gasket, strip, foam, adhesive, 3/8 x 1/8 |  |  | 
	| 1E | 12H3015 | Panel, front, top, subassy |  |  | 
	| 1F | F2028200 | Washer, retaining, .50 OD, nylon |  |  | 
	| 2 | 12H3003 | Panel, front, middle, assembly, LMH |  |  | 
	| 2A | 12H7002 | Panel, front, middle, plastic |  |  | 
	| 2B | A2117600 | Gauge, press/temp, remote |  |  | 
	| 2C | RE2333500 | Switch, Rocker, 120V, amber |  |  | 
	| 2D | 12H3008 | Display module, electronic |  |  | 
	| 2E | E2318900 | Hinge, front panel, middle |  |  | 
	| 2F | E2335100 | Circuit Breaker, 10 Amp, 120V |  |  | 
	| 2G | 12H3017 | Circuit Breaker, 2A, 120V |  |  | 
	| 2H | 1-418 | Support, middle panel |  |  | 
	| 2I | F2027100 | Screw, #6 x 3/8" thd forming for plastic |  |  | 
	| 2J | F2015900 | Screw, #8-32 x 3/8", phil pan hd |  |  | 
	| 2K | F2028300 | Rivet, pop, 3/16 diameter |  |  | 
	| 2L | E2334501 | Latch, magnet, .56 dia, 3.1 lbs |  |  | 
	| 2M | E2334502 | Harness, wire, power switch/circuit breaker |  |  | 
	| 2N | E2334502 | Harness, wire, display/+24V circuit breaker |  |  | 
	| 3 | 12H3004 | Panel, front, bottom, assembly |  |  | 
	| 3A | 12H7050 | Control, programmed |  |  | 
	| 3B | 12H7004 | Bracket, mounting, control |  |  | 
	| 3C | 12H7003 | Panel, front, bottom, plastic |  |  | 
	| 3D | 12H3007 | Hinge, front panel, bottom |  |  | 
	| 3E |  | Rivet, pop, 3/16 diameter |  |  | 
	| 3F |  | Screw, #8-32 x 3/8", phil pan hd |  |  | 
	| 3G |  | Washer, retaining, .50 od, nylon |  |  | 
	| 3H |  | Screw, captive, .19 x .54 fast lead, phil pan hd |  |  | 
	| 4 | 12H3019 | Panel, left side |  |  | 
	| 5 | 12H3018 | Panel, right side |  |  | 
	 |  | BASE JACKET ASSEMBLY |  |  | 
	| 6 | 12H3001 | Base, jacket, assembly |  |  | 
	| 6A | 12H3011 | Base, jacket |  |  | 
	| 6B | F2001900 | Screw, 8-32unc x 1.5l |  |  | 
	| 6C | 12H3012 | Bracket, wall attach |  |  | 
	| 6D | F2011600 | Screw, hex head, 1/4-20 unc x .75" lg. |  |  | 
	| 6E | 10-103 | Nut, flange, serrated, hex head, 1/4" |  |  | 
	| 6F | 12H3010 | Bracket, hx, right side |  |  | 
	| 6G | 12H3016 | Bracket, hx, left side |  |  | 
	| 6H | F2027000 | Screw, #8-18 x 1/2, phil pan hd |  |  | 
	| 6I | E2334900 | Switch, pressure, air/gas, inlet |  |  | 
	| 6J | R0021300 | Transformer,40Va, 115V/24V |  |  | 
	| 6K | 12H3009 | Bracket, transformer |  |  | 
	| 6L | F2015900 | Rivet, pop, 3/16 diameter |  |  | 
	 |  | HEAT EXCHANGER CABINET |  |  | 
	| 7A | S2114000 | Grommet, pipe, wire, multi size, rubber |  |  | 
	| 7B | S2113800 | Heat exchanger |  |  | 
	| 7BB | 12H5501 | Gasket, vent adapter |  |  | 
	| 7C | 12H3023 | Washer, clamping, hx bracket |  |  | 
	| 7D | F2023700 | Washer, M5, lock, internal tooth |  |  | 
	| 7E | F2025300 | Screw, M5-0.8 X 14mm, soc Hd |  |  | 
	| 7G | S2105400 | Gasket, blower fan |  |  | 
	| 7H | F2027000 | Screw, #8-18 x 1/2, phil pan hd |  |  | 
	| 7I | P2074500 | Vent, air, auto, 1/4" bspp |  |  | 
	| 7J | 12H4010 | Pipe, air vent |  |  | 
	| 7K | RE2320600 | Sensor, temperature, water, 1/4" npt |  |  | 
	| 7L | F2015900 | Rivet, pop, 3/16 diameter |  |  | 
	| 7M | E0005501 | Terminal, 1/4" push-on, male, red |  |  | 
	| 7N | S2113800 | Heat exchanger |  |  | 
	| 7O | RA2107500 | Blower, combustion air |  |  | 
	| 7P | F2027700 | Washer, sealing, .410 OD |  |  | 
	| 7Q | 12H5002 | Plate, venturi |  |  | 
	| 7R | F2029300 | Screw, m5 x 8, soc hd cap |  |  | 
	| 7S | S2116000 | Oring, 2 1/8 id x 3/32 thick |  |  | 
	| 7T | 12H5500 | Adapter, vent, cpvc |  |  | 
	| 7U | 500-168 | Plug, hex, 1/8" npt |  |  | 
	| 7V | RE2319700 | Sensor, temperature, air, 1 /4" bsp, 1.85 l |  |  | 
	| 7W | RE2319900 | Sensor, temperature, water, duplex |  |  | 
	 |  | BURNER COMPONENTS |  |  | 
	| 1 | R2069102 | Burner, main |  |  | 
	| 2 | RS2108500 | Gasket, burner |  |  | 
	| 3 | RT2109000 | Tile, refractory, front, combustion chamber |  |  | 
	| 4 | R2069300 | Ignitor, spark, w/gasket |  |  | 
	| 5 | R2069200 | Flame sensor, w/gasket |  |  | 
	| 6 | RS2108300 | Burner door with gaskets |  |  | 
	| 7 | RS2108400 | Air/gas channel |  |  | 
	| 8 | RS2108400 | Screw, air/gas channel |  |  | 
	| 10 | RS2111200 | Heat exchanger |  |  | 
	| 11 | RW2013300 | Gasket, ignitor |  |  | 
	| 12 | 62108300 | Burner door, w/gaskets |  |  | 
	| 13 | R50D2021 | Repair kit, rear refractory tile |  |  | 
	| 14 |  | Gaskets-only (burner door) |  |  | 
	| 15 |  | Screw, ignitor/flame sensor, M4-.7X8MM |  |  | 
	| 16 | RW2013300 | Ignitor gasket |  |  | 
	| 17 | RW2013400 | Flame/sensor gasket |  |  | 
	 |  | PUMP ASSSEMBLY |  |  | 
	| 8 |  | Pump assembly |  |  | 
	| 8A | 12H4012 | Bracket, control valve |  |  | 
	| 8B | A2117500 | Trap, condensate, small capacity |  |  | 
	| 8C | F2029400 | Screw, M4 x 10, soc hd cap |  |  | 
	| 8D | V2020600 | Valve, gas |  |  | 
	| 8E | S2114800 | Bumper, rubber, 21/32" base dia. x 1/2"height, 5/32" thru hole |  |  | 
	| 8F |  | Washer, sealing, 0.93 OD x 0.62 ID |  |  | 
	| 8G |  | Pipe, 3 way valve to dhw |  |  | 
	| 8H | 12H4019 | Bracket, 3 way valve |  |  | 
	| 8I | F2027000 | Screw, #8-18 x 1/2, phil pan hd |  |  | 
	| 8J | F2027000 | Bracket, capture, hex |  |  | 
	| 8K | 12H4022 | Valve, three way, with actuator |  |  | 
	| 8L | A2117802 | Pump |  |  | 
	| 8M | A2117700 | Screw, 6-20 x 1/2" l self tapping |  |  | 
	| 8N | F0024200 | Sensor, temperature, dhw, 1/4" npt |  |  | 
	| 😯 | E2337500 | Exchanger, heat, plate |  |  | 
	| 8P | F2029100 | Tie, cable, 14-3/4 long x 0.31" wide,heat stabilized |  |  | 
	| 8Q | E2337400 | Flow switch, water |  |  | 
	| 8R | 12H4023 | Pipe, tailpiece, 1" npt M x 3/4 tube, cu |  |  | 
	| 8S | S2116300 | O-ring, -120, 1" ID x 1-3/16" OD |  |  | 
	| 8T | P2067603 | Pipe, pvc, 3/4" sch 40 |  |  | 
	| 8U | E0005501 | Terminal, 1/4" push-on, male, red |  |  | 
	| 8V | E0005502 | Terminal, 1/4" push-on, female, red |  |  | 
	 |  | PLUMBING COMPONENTS |  |  | 
	| P1 | A2117400 | Tank, expansion, rect, 10 liter |  |  | 
	| P2 | 12H3020 | Bracket weldment, expansion tank |  |  | 
	| P3 | S2114000 | Grommet, pipe, wire, multi size, rubber |  |  | 
	| P4 | 12H4011 | Pipe, gas |  |  | 
	| P5 | S2115100 | O-ring, 20.04 mm ID x 27.10 mm OD |  |  | 
	| P6 | 12H4004 | Pipe, pump to hx inlet |  |  | 
	| P7 | 12H4001 | Pipe, hx outlet to dhw |  |  | 
	| P8 | P2074600 | Switch, press, 3-30 psi, 1/4" bspp |  |  | 
	| P9 | 12H3006 | Gasket, expansion tank |  |  | 
	| P10 | 10-596 | Tee, 1/4" barb, plastic |  |  | 
	| P11 | F2027500 | Washer, sealing, .59 OD x .32 ID x .06 poly |  |  | 
	| P12 | 12H4006 | Pipe, expansion tank |  |  | 
	| P13 | F2025502 | Washer, sealing, 0.93 OD x 0.62 ID |  |  | 
	| P14 | F2027700 | Washer, sealing, .410 OD |  |  | 
	| P15 | E2336500 | Switch, pressure, 3.80" w.c. set point |  |  | 
	| P16 | 12H2500 | Hose, drain, condensate |  |  | 
	| P17 | F2028400 | Tie, cable, heat stabilized, 5" |  |  | 
	| P18 | Q0078800 | Tube, silicone, .188 ID x .318 OD x 23" long |  |  | 
	| P19 | F2029000 | Cotter pin, horse shoe, 1/8, zinc pl |  |  | 
	 | E2337600 | Harness, wire, main |  |  | 
	 | 12H7009 | Connector assembly |  |  | 
	 | 12H7008 | Relay, 24vac, Dpdt 8 |  |  | 
	 | 12H7010 | Harness, wire, main, heat only 2 |  |  | 
	 | E2337600 | Harness, wire, main, lmc |  |  | 
	 | 12H7005 | Wire, spark ignition |  |  | 
	 | 12H7006 | Wire assy, flame sensor |  |  | 
	 | E2334500 | Plug, 3 prong, with cord, 14 awg 7 |  |  |